 
    技術文章
Technical articles 熱門搜索:
    
    
      發那科伺服放大器報警代碼整理詳情了解
    
      廣州數控GSK980TD系統故障報警分析
    
      全系列ABB變頻器ACS88*代碼F0010報警維修
    
      FANUC數控系統常見故障及解決方法
    
    
    
      松下伺服驅動器常見故障報代碼維修
    
      ABB變頻器顯示故障代碼4280維修處理
    
      發那科數控系統報警代碼大全
    
      西門子840D數控系統報21612 故障處理及分析
    
    
    
      施耐德軟啟動器之常見故障報警解決辦法
    
      全系列施耐德變頻器維修報警代碼方法
    
      全系列OTIS奧的斯變頻器ACA21290BA4常見故障維修
    
      驅動器維修報警 1、2、3、4、5、6、發那科驅動器維修
    
    
    
      全系列施耐德觸摸屏常見的故障維修
    
      施耐德變頻器顯示OBF/PRA/NLP/NST故障維修
    
      全系列ABB變頻器無報警卻不能在遠程啟動故障維修
    
      全系列庫卡(kuka)機器人示教器常見故障維修
熱門搜索:
    
    
      發那科伺服放大器報警代碼整理詳情了解
    
      廣州數控GSK980TD系統故障報警分析
    
      全系列ABB變頻器ACS88*代碼F0010報警維修
    
      FANUC數控系統常見故障及解決方法
    
    
    
      松下伺服驅動器常見故障報代碼維修
    
      ABB變頻器顯示故障代碼4280維修處理
    
      發那科數控系統報警代碼大全
    
      西門子840D數控系統報21612 故障處理及分析
    
    
    
      施耐德軟啟動器之常見故障報警解決辦法
    
      全系列施耐德變頻器維修報警代碼方法
    
      全系列OTIS奧的斯變頻器ACA21290BA4常見故障維修
    
      驅動器維修報警 1、2、3、4、5、6、發那科驅動器維修
    
    
    
      全系列施耐德觸摸屏常見的故障維修
    
      施耐德變頻器顯示OBF/PRA/NLP/NST故障維修
    
      全系列ABB變頻器無報警卻不能在遠程啟動故障維修
    
      全系列庫卡(kuka)機器人示教器常見故障維修
    
     更新時間:2023-02-15
更新時間:2023-02-15 點擊次數:1169
點擊次數:1169
              E250 Heatsink Overtemperature Warning散熱器過熱警告。
Description:說明:
The temperature of the heatsink in the drive controller has reached the
maximum allowable temperature. Within a time frame of 30 seconds, the
drive follows the command value input. Consequently, there exists the
possibility to shut down the motor with the control so that it remains true to
the process. (For example close the operation, leave the collision area,
etc.) After 30 seconds, the parameter "Best Possible Deceleration, P-0-
0119" set reaction appears during operation.
驅動器控制器中的散熱器溫度已達到最高允許溫度。在30秒內驅動器遵循命令值輸入。因此,存在使用控制裝置關閉電機的可能性,使其保持正確這一過程。(例如,關閉操作,離開碰撞區域,30秒后,參數“最佳可能減速,P-0-0119“設置反應在操作過程中出現。
Cause:原因:
1. Deficiency of the drive's internal blower.
2. Deficiency of the control cabinet’s climate control.
3. Incorrect control cabinet dimensioning regarding the
head ventilation
1.驅動器內部鼓風機不足。
2.控制柜氣候控制不足。
3.控制柜尺寸不正確頭部通風

Remedy:
For 1. If the blower fails exchange the drive controller.
For 2. Install climitization feature to the cabinet.
For 3. Check the dimensions of the control cabinet.
對于1。如果鼓風機出現故障,更換驅動控制器。
對于2。為機柜安裝氣候調節功能。
對于3。檢查控制柜的尺寸。
F895 4 kHz Signal Error4 kHz信號錯誤。
Description:
The 4kHz signal is synchronized with the software processing for creation
of the resolver signal. This error message is created when
synchronization occurs improperly.
4kHz信號與用于創建的軟件處理同步旋轉變壓器信號的。此錯誤消息是在以下情況下創建的同步發生不正確。
Cause:
1. The synchronization of the resolver controller voltage is invalid
in regards to the software.
2. The error can be produced through an electrical discharge.
1.分解器控制器電壓同步無效關于軟件。
2.該誤差可通過放電產生。
Remedy:補救措施:
For 1. Exchange drive controller and return for testing.
For 2. Power down and then on. If this in not successful; exchange
drive controller.
對于1。更換驅動器控制器并返回測試。
對于2。關閉電源,然后打開。如果這不成功;交換驅動控制器。